Buff Daddy Shipping Contact About Cart KBM





















Part Number:
1033
 Actual Diameter:
2 - 7/8"
 Height:
1/2"
 Backing Material:
MICRO HOOK/LOOP
Need to sand something that is super curvy, or oddly shaped?  You'll want one of these 3" interface pads!  It's 1/2" height will enable a sanding disc to reach its maximum "flex" potential.  The micro-hook face firmly locks discs into place, and will not protrude into the face of the disc.  A nice addition to your interface arsenal.
Price:
$6.91
Qty:
Mirka 3" Soft-Faced Interface Pad- 1/2" thick

Mirka 3" Soft-Faced Interface Pad- 1/2" thick

Mirka 3" Soft-Faced Interface Pad- 1/2" thick
Mirka 1033 | 3" Velcro Interface Pad • 1/2" tall<br/><br/>The Mirka 1033 3" Velcro Interface Pad utilizes low-profile micro hooks, which strongly secure sanding discs into place (even during heavy friction, high RPM sanding).<br/><br/>When sanding using thin or flimsy sanding discs, short hooks ensure a flat and consistent cut, and lessen the potential for "hook marking" of the sanding surface.<br/><br/> Matched low-profile Velcro loops keep the interface pad tightly attached to the backing plate, which minimizes friction-induced heat caused by rapid & repeated shifting of the hooks and loops.<br/><br/>Mirka 9133 | 1033 | 9947 | 3" Velcro Interface Pads<br/><br/>This trio of Mirka 3" Interface Pads can improve the performance of any Velcro-backed sanding disc. The Mirka 1033 and 9133 include a cushiony foam interlayer (sandwiched between layers of hook and loop Velcro), which helps sanding discs to readily conform to complex surfaces. They also help to compensate for inadvertent tilting of the machine during sanding.<br/><br/>The Mirka 9133 and 9947 were originally designed for use with Mirka Abranet and Autonet Sanding Discs, but can be used with other types of disc as well.<br/><br/>Mirka 9947 | 3" Abranet Pad Protector • 1/16" tall<br/><br/>The Mirka 9947 3" Abranet Pad Protector is designed to to be used with Abranet and Autonet sanding discs. The open mesh design employed in Abranet and Autonet products allow the backing plate's Velcro-style hooks to protrude through the mesh. If this occurs, the hooks can degrade quickly, AND cause marring of the surface being sanded!<br/><br/>Avoid this problem by installing a Pad Protector. This simple device will not only protect the backing plate and surface being sanded, it also increases adhesion of the sanding disc to the backing plate.<br/><br/>Mirka 9133 | 3" Abranet Velcro Interface Pad • 3/16" tall<br/><br/>The Mirka 9133 3" Abranet Interface Pad is designed to to be used with Abranet and Autonet sanding discs. The open mesh design employed in Abranet and Autonet products allow the backing plate's Velcro-style hooks to protrude through the mesh. If this occurs, the hooks can degrade quickly, AND cause marring of the surface being sanded!<br/><br/>Avoid problems by installing this interface pad (or the Mirka 9947 Pad Protector). Specialized hooks eliminate the potential for damage to the surface being sanded, and efficiently grab ahold of Abranet and Autonet Net Mesh Discs.<br/><br/>1033 | 1066 | 1066F | 1066SF<br/>  Mirka Velcro Interface Pads<br/><br/>When a sanding disc is mounted directly onto a backing plate, its ability to contour is limited by plate rigidity. Although leveling capability might increase, edge-digging is likely to occur. Full-width utiliztion of the disc becomes difficult when sanding complex surfaces. When an interface pad is installed between the backing plate and disc, contourability increases.<br/><br/>If the machine is tilted off-kilter, the interface pad aids in keeping the full width of the disc in complete contact with the sanding surface. Attempting to sand using a small section of a disc can be difficult; an interface pad can make all the difference.<br/><br/>Mirka 3" Sanding Products<br/>1033 | MR-350 | Q.Silver Sanding Discs<br/><br/>Mirka Q.Silver 3" & 6" Sanding Discs<br/>Mirka Q.Silver Discs can take a lot of abuse, as the resin (adhesive) used to attach its abrasive grains to the disc is very resistant to heat. Mirka Q.Silver Discs can be used wet or dry. Depending upon the grade, Q.Silver Discs utilize various weights of paper (or thickness) and abrasive grains (alumunum oxide or silicon carbide). Q.Silver Sanding Discs are available in the following grades:<br/><br/>3" diameter<br/>2B-608-080 (P080) | 2B-608-120 (P120)<br/>2B-608-150 (P150) | 2B-608-180 (P180)<br/>2B-608-220 (P220) | 2B-608-320 (P320)<br/>2B-608-400 (P400) | 2C-608-600 (P600)<br/>2C-608-800 (P800) | 2C-608-1000 (P1000)<br/>2C-608-1200 (P1200) | 2C-608-1500 (P1500)<br/><br/>6" diameter<br/>2B-622-080 (P080) | 2B-622-120 (P120)<br/>2B-622-150 (P150) | 2B-622-180 (P180)<br/>2B-622-220 (P220) | 2B-622-240 (P240)<br/>2B-622-320 (P320) | 2B-622-400 (P400)<br/>2B-622-500 (P500) | 2C-622-600 (P600)<br/>2C-622-800 (P800) | 2C-622-1000 (P1000)<br/>2C-622-1200 (P1200) | 2C-622-1500 (P1500)<br/><br/>Mirka 3" & 6" Interface Pads<br/>A wide variety of interface pads ensure that just about any sanding disc can deliver maximum performance while working on any sanding surface. Mirka offers interface pads with no foam, skinny foam, fat foam, stiff foam, and soft foam.<br/><br/>Mirka MR-350 3" Bulldog Palm Sander<br/>5mm orbit diameter | 0-12,000 RPM<br/><br/>Mirka 3" Sanding Products<br/>9133 | MR-350 | Microstar Discs<br/><br/>Mirka Microstar 3" & 6" Dry-Sanding Discs are designed for use without water. They are engineered to absolutely resist debris loading. Since no water is used during sanding, it is much easier to gauge sanding results. Microstar Dry-Sanding Discs are available in the following grades:<br/><br/>3" diameter<br/>FM-608-800 (P800) | FM-608-1000 (P1000)<br/>FM-608-1200 (P1200) | FM-608-1500 (P1500)<br/>FM-608-2000 (P2000) | FM-608-2500 (P2500)<br/><br/>6" diameter<br/>FM-622-800 (P800) | FM-622-1000 (P1000)<br/>FM-622-1200 (P1200) | FM-622-1500 (P1500)<br/>FM-622-2000 (P2000) | FM-622-2500 (P2500)<br/><br/>Mirka 3" & 6" Interface Pads<br/>A wide variety of interface pads ensure that just about any sanding disc can deliver maximum performance while working on any sanding surface. Mirka offers interface pads with no foam, skinny foam, fat foam, stiff foam, and soft foam.<br/><br/>Mirka MR-350 3" Bulldog Palm Sander<br/>5mm orbit diameter | 0-12,000 RPM<br/><br/>About Mirka Interface Pads<br/><br/>Interface Pads are placed between backing plates and sanding discs, with the intent to substantially improve overall sanding performance. Interface pads enable sanding discs to conform to their maximum ability.They also assist in distributing machine weight, and user-applied pressure.<br/><br/>An interface pad can decrease uncontrolled wandering of the machine, which occurs when a disc cannot conform to the surface being sanded (due to backing plate rigidity). If the choice is made to use only a portion of the disc by intentionally tilting the machine, the portion in contact with the sanding surface receives adequate support from the interface pad.<br/><br/>HP3-VELCRO<br/>3" Dome-Shaped Velcro Hand Sanding Pad.<br/><br/>Shown with the included 3" Foam Velcro Interface Pad.<br/><br/>HP3-VELCRO<br/><br/>3" Dome-Shaped Velcro Hand Sanding Pad.<br/><br/>Left: Shown with a Mirka® Autonet Mesh Fabric Sanding Disc, and a Mirka 9947 Pad Protector.<br/>Right: Shown with a Mirka® 1033 3" Foam Velcro Interface Pad.<br/><br/>HP3-VELCRO<br/>3" Velcro Dome Hand Sanding Pad.<br/><br/>Shown with Mirka 9133 3" Abranet Velcro Interface Pad.<br/><br/>HP3-VELCRO<br/>3" Velcro Dome Hand Sanding Pad.<br/><br/>Shown with Mirka 9133 3" Abranet Velcro Interface Pad, and a 3" Autonet Mesh Fabric Sanding Disc.<br/><br/>
Click to enlarge image(s)


A quality interface pad, for just about any sanding task.

The time may come when you'll need to sand a sphere-shaped item, a cylinder, or a wickedly-curved fender. To achieve maximum cushioning and shapability of the sanding disc, this is the interface pad you'll need. The Mirka 1033 3" Velcro Interface Pad measures 3" in diameter, and is 1/2" tall. Also available in a 6" version: 1066SF

Note that due to its height, this interface pad may lessen sanding disc movement, particularly if paired with small stroke machines. Please view photos for more information.

Add a Dome-Style Hand Sanding Pad. This uniquely shaped block makes sanding by hand a breeze to accomplish. Its yellow cushiony material is soft, making it easy to grasp, even when wet. The Velcro face is molded into place (not glued), so pad failure is  unlikely. A soft interface pad is included (interface is not a Mirka product).

 Mirka 3" Velcro Backing Plates can be found here.

 Mirka 3" Velcro Interface Pads: 1033 | 9947 | 9133

 Mirka 3" Velcro Sanding Discs can be found here:
        Abralon | Abranet | Autonet | Silver | Microstar

 More Interface Pad info: Interface Pad Facts.

Part Number:
9947
 Actual Diameter:
2 - 7/8"
 Height:
1/8"
 Backing Material:
HOOK/LOOP
This 3" pad protector is designed for use with Mirka net mesh products (such as Abranet® and Autonet™ discs). It will prevent the backing plate hook material from protruding through the disc.  Sand without one, and backing plate damage or surface marring may occur. They're inexpensive and durable.  Don't skimp- use one!
Price:
$3.82
Qty:
Mirka Abranet® 3" Pad Protector- 1/8" thick

Mirka Abranet® 3" Pad Protector- 1/8" thick

Mirka Abranet® 3" Pad Protector- 1/8" thick
Mirka 9947 | 3" Abranet Pad Protector • 1/16" tall<br/><br/>The Mirka 9947 3" Abranet Pad Protector is designed to to be used with Abranet and Autonet sanding discs. The open mesh design employed in Abranet and Autonet products allow the backing plate's Velcro-style hooks to protrude through the mesh. If this occurs, the hooks can degrade quickly, AND cause marring of the surface being sanded!<br/><br/>Avoid this problem by installing a Pad Protector. This simple device will not only protect the backing plate and surface being sanded, it also increases adhesion of the sanding disc to the backing plate.<br/><br/>Mirka 9133 | 1033 | 9947 | 3" Velcro Interface Pads<br/><br/>This trio of Mirka 3" Interface Pads can improve the performance of any Velcro-backed sanding disc. The Mirka 1033 and 9133 include a cushiony foam interlayer (sandwiched between layers of hook and loop Velcro), which helps sanding discs to readily conform to complex surfaces. They also help to compensate for inadvertent tilting of the machine during sanding.<br/><br/>The Mirka 9133 and 9947 were originally designed for use with Mirka Abranet and Autonet Sanding Discs, but can be used with other types of disc as well.<br/><br/>Mirka 9133 | 3" Abranet Velcro Interface Pad • 3/16" tall<br/><br/>The Mirka 9133 3" Abranet Interface Pad is designed to to be used with Abranet and Autonet sanding discs. The open mesh design employed in Abranet and Autonet products allow the backing plate's Velcro-style hooks to protrude through the mesh. If this occurs, the hooks can degrade quickly, AND cause marring of the surface being sanded!<br/><br/>Avoid problems by installing this interface pad (or the Mirka 9947 Pad Protector). Specialized hooks eliminate the potential for damage to the surface being sanded, and efficiently grab ahold of Abranet and Autonet Net Mesh Discs.<br/><br/>Mirka 1033 | 3" Velcro Interface Pad • 1/2" tall<br/><br/>The Mirka 1033 3" Velcro Interface Pad utilizes low-profile micro hooks, which strongly secure sanding discs into place (even during heavy friction, high RPM sanding).<br/><br/>When sanding using thin or flimsy sanding discs, short hooks ensure a flat and consistent cut, and lessen the potential for "hook marking" of the sanding surface.<br/><br/> Matched low-profile Velcro loops keep the interface pad tightly attached to the backing plate, which minimizes friction-induced heat caused by rapid & repeated shifting of the hooks and loops.<br/><br/>1033 | 1066 | 1066F | 1066SF<br/> Mirka Velcro Interface Pads<br/><br/>When a sanding disc is mounted directly onto a backing plate, its ability to contour is limited by plate rigidity. Although leveling capability might increase, edge-digging is likely to occur. Full-width utiliztion of the disc becomes difficult when sanding complex surfaces. When an interface pad is installed between the backing plate and disc, contourability increases.<br/><br/>If the machine is tilted off-kilter, the interface pad aids in keeping the full width of the disc in complete contact with the sanding surface. Attempting to sand using a small section of a disc can be difficult; an interface pad can make all the difference.<br/><br/>Mirka 3" Sanding Products<br/>1033 | MR-350 | Q.Silver Sanding Discs<br/><br/>Mirka Q.Silver 3" & 6" Sanding Discs<br/>Mirka Q.Silver Discs can take a lot of abuse, as the resin (adhesive) used to attach its abrasive grains to the disc is very resistant to heat. Mirka Q.Silver Discs can be used wet or dry. Depending upon the grade, Q.Silver Discs utilize various weights of paper (or thickness) and abrasive grains (alumunum oxide or silicon carbide). Q.Silver Sanding Discs are available in the following grades:<br/><br/>3" diameter<br/>2B-608-080 (P080) | 2B-608-120 (P120)<br/>2B-608-150 (P150) | 2B-608-180 (P180)<br/>2B-608-220 (P220) | 2B-608-320 (P320)<br/>2B-608-400 (P400) | 2C-608-600 (P600)<br/>2C-608-800 (P800) | 2C-608-1000 (P1000)<br/>2C-608-1200 (P1200) | 2C-608-1500 (P1500)<br/><br/>6" diameter<br/>2B-622-080 (P080) | 2B-622-120 (P120)<br/>2B-622-150 (P150) | 2B-622-180 (P180)<br/>2B-622-220 (P220) | 2B-622-240 (P240)<br/>2B-622-320 (P320) | 2B-622-400 (P400)<br/>2B-622-500 (P500) | 2C-622-600 (P600)<br/>2C-622-800 (P800) | 2C-622-1000 (P1000)<br/>2C-622-1200 (P1200) | 2C-622-1500 (P1500)<br/><br/>Mirka 3" & 6" Interface Pads<br/>A wide variety of interface pads ensure that just about any sanding disc can deliver maximum performance while working on any sanding surface. Mirka offers interface pads with no foam, skinny foam, fat foam, stiff foam, and soft foam.<br/><br/>Mirka MR-350 3" Bulldog Palm Sander<br/>5mm orbit diameter | 0-12,000 RPM<br/><br/>Mirka 3" Sanding Products<br/>9133 | MR-350 | Microstar Discs<br/><br/>Mirka Microstar 3" & 6" Dry-Sanding Discs are designed for use without water. They are engineered to absolutely resist debris loading. Since no water is used during sanding, it is much easier to gauge sanding results. Microstar Dry-Sanding Discs are available in the following grades:<br/><br/>3" diameter<br/>FM-608-800 (P800) | FM-608-1000 (P1000)<br/>FM-608-1200 (P1200) | FM-608-1500 (P1500)<br/>FM-608-2000 (P2000) | FM-608-2500 (P2500)<br/><br/>6" diameter<br/>FM-622-800 (P800) | FM-622-1000 (P1000)<br/>FM-622-1200 (P1200) | FM-622-1500 (P1500)<br/>FM-622-2000 (P2000) | FM-622-2500 (P2500)<br/><br/>Mirka 3" & 6" Interface Pads<br/>A wide variety of interface pads ensure that just about any sanding disc can deliver maximum performance while working on any sanding surface. Mirka offers interface pads with no foam, skinny foam, fat foam, stiff foam, and soft foam.<br/><br/>Mirka MR-350 3" Bulldog Palm Sander<br/>5mm orbit diameter | 0-12,000 RPM<br/><br/>About Mirka Pad Protectors<br/><br/>Close-up shot of a Mirka Abranet Net Mesh Sanding Disc, attached to an Abranet Pad Protector. Without the Pad Protector, the white hooks of the backing plate would very likely protrude through the disc, resulting in damage to the backing plate and the surface being sanded. Always use a Pad Protector with net mesh discs.<br/><br/>Working on curved or complex shapes? To maximize flexibility of net mesh discs, install a purpose-built Abranet Interface Pad between the backing plate and disc. Abranet Interface Pads feature a low profile piece of foam, which is sandwiched between the same type of hook and loop material used to make Abranet Pad Protectors.<br/><br/>HP3-VELCRO<br/>3" Dome-Shaped Velcro Hand Sanding Pad.<br/><br/>Shown with the included 3" Foam Velcro Interface Pad.<br/><br/>HP3-VELCRO<br/><br/>3" Dome-Shaped Velcro Hand Sanding Pad.<br/><br/>Left: Shown with a Mirka® Autonet Mesh Fabric Sanding Disc, and a Mirka 9947 Pad Protector.<br/>Right: Shown with a Mirka® 1033 3" Foam Velcro Interface Pad.<br/><br/>HP3-VELCRO<br/>3" Velcro Dome Hand Sanding Pad.<br/><br/>Shown with Mirka 9133 3" Abranet Velcro Interface Pad.<br/><br/>HP3-VELCRO<br/>3" Velcro Dome Hand Sanding Pad.<br/><br/>Shown with Mirka 9133 3" Abranet Velcro Interface Pad, and a 3" Autonet Mesh Fabric Sanding Disc.<br/><br/>
Click to enlarge image(s)


Designed for use with Abranet and Autonet Sanding Discs.

The open mesh design employed in Abranet and Autonet products may allow the hook material of a backing plate to protrude through the mesh. If this occurs, the backing plate hooks will degrade quickly. Even worse, the hook material can cause surface marring! Avoid this problem by installing a Pad Protector. Also available in a 6" version: 9956

This simple device will not only protect the backing plate and surface being sanded, it also increases adhesion of the sanding disc to the backing plate. Since the Pad Protector is only about 1/16" thick, in most cases it will not affect the leveling capability of the disc.

Add a Dome-Style Hand Sanding Pad. This uniquely shaped block makes sanding by hand a breeze to accomplish. Its yellow cushiony material is soft, making it easy to grasp, even when wet. The Velcro face is molded into place (not glued), so pad failure is  unlikely. A soft interface pad is included (interface is not a Mirka product).

Add an interface pad. The time may come when you'll need to sand a sphere-shaped item, a cylinder, or a wickedly-curved fender. To increase cushioning and shapability of net mesh sanding discs, this is the interface pad you'll need. The Mirka 9133 3" Abranet Interface Pad measures 2-7/8" in diameter, and is 3/16" tall. Note that due to its height, this interface pad may lessen sanding disc movement, particularly if paired with small stroke machines. Also available in a 6" version: 9166

Mirka 3" Velcro Backing Plates can be found here.

Mirka 3" Velcro Interface Pads: 1033 | 9947 | 9133

Mirka 3" Velcro Sanding Discs can be found here:
        Abralon | Abranet | Autonet | Silver | Microstar

More Interface Pad info: Interface Pad Facts.

Part Number:
9133
 Actual Diameter:
2 - 7/8"
 Height:
3/8"
 Backing Material:
HOOK/LOOP
This 3" interface pad is designed for use with Mirka net mesh products (such as Abranet® and Autonet™ discs). What's so different about it? The hooks! They're pliable and long, with tips that are shaped to grab ahold of the loop. They bend easily to resist marring, yet really lock net mesh discs safely into place.
Price:
$4.35
Qty:
Mirka Abranet® 3" Interface Pad- 3/8" thick

Mirka Abranet® 3" Interface Pad- 3/8" thick

Mirka Abranet® 3" Interface Pad- 3/8" thick
Mirka 9133 | 3" Abranet Velcro Interface Pad • 3/16" tall<br/><br/>The Mirka 9133 3" Abranet Interface Pad is designed to to be used with Abranet and Autonet sanding discs. The open mesh design employed in Abranet and Autonet products allow the backing plate's Velcro-style hooks to protrude through the mesh. If this occurs, the hooks can degrade quickly, AND cause marring of the surface being sanded!<br/><br/>Avoid problems by installing this interface pad (or the Mirka 9947 Pad Protector). Specialized hooks eliminate the potential for damage to the surface being sanded, and efficiently grab ahold of Abranet and Autonet Net Mesh Discs.<br/><br/>Mirka 9133 | 1033 | 9947 | 3" Velcro Interface Pads<br/><br/>This trio of Mirka 3" Interface Pads can improve the performance of any Velcro-backed sanding disc. The Mirka 1033 and 9133 include a cushiony foam interlayer (sandwiched between layers of hook and loop Velcro), which helps sanding discs to readily conform to complex surfaces. They also help to compensate for inadvertent tilting of the machine during sanding.<br/><br/>The Mirka 9133 and 9947 were originally designed for use with Mirka Abranet and Autonet Sanding Discs, but can be used with other types of disc as well.<br/><br/>Mirka 9947 | 3" Abranet Pad Protector • 1/16" tall<br/><br/>The Mirka 9947 3" Abranet Pad Protector is designed to to be used with Abranet and Autonet sanding discs. The open mesh design employed in Abranet and Autonet products allow the backing plate's Velcro-style hooks to protrude through the mesh. If this occurs, the hooks can degrade quickly, AND cause marring of the surface being sanded!<br/><br/>Avoid this problem by installing a Pad Protector. This simple device will not only protect the backing plate and surface being sanded, it also increases adhesion of the sanding disc to the backing plate.<br/><br/>Mirka 1033 | 3" Velcro Interface Pad • 1/2" tall<br/><br/>The Mirka 1033 3" Velcro Interface Pad utilizes low-profile micro hooks, which strongly secure sanding discs into place (even during heavy friction, high RPM sanding).<br/><br/>When sanding using thin or flimsy sanding discs, short hooks ensure a flat and consistent cut, and lessen the potential for "hook marking" of the sanding surface.<br/><br/> Matched low-profile Velcro loops keep the interface pad tightly attached to the backing plate, which minimizes friction-induced heat caused by rapid & repeated shifting of the hooks and loops.<br/><br/>1033 | 1066 | 1066F | 1066SF<br/> Mirka Velcro Interface Pads<br/><br/>When a sanding disc is mounted directly onto a backing plate, its ability to contour is limited by plate rigidity. Although leveling capability might increase, edge-digging is likely to occur. Full-width utiliztion of the disc becomes difficult when sanding complex surfaces. When an interface pad is installed between the backing plate and disc, contourability increases.<br/><br/>If the machine is tilted off-kilter, the interface pad aids in keeping the full width of the disc in complete contact with the sanding surface. Attempting to sand using a small section of a disc can be difficult; an interface pad can make all the difference.<br/><br/>Mirka 3" Sanding Products<br/>1033 | MR-350 | Q.Silver Sanding Discs<br/><br/>Mirka Q.Silver 3" & 6" Sanding Discs<br/>Mirka Q.Silver Discs can take a lot of abuse, as the resin (adhesive) used to attach its abrasive grains to the disc is very resistant to heat. Mirka Q.Silver Discs can be used wet or dry. Depending upon the grade, Q.Silver Discs utilize various weights of paper (or thickness) and abrasive grains (alumunum oxide or silicon carbide). Q.Silver Sanding Discs are available in the following grades:<br/><br/>3" diameter<br/>2B-608-080 (P080) | 2B-608-120 (P120)<br/>2B-608-150 (P150) | 2B-608-180 (P180)<br/>2B-608-220 (P220) | 2B-608-320 (P320)<br/>2B-608-400 (P400) | 2C-608-600 (P600)<br/>2C-608-800 (P800) | 2C-608-1000 (P1000)<br/>2C-608-1200 (P1200) | 2C-608-1500 (P1500)<br/><br/>6" diameter<br/>2B-622-080 (P080) | 2B-622-120 (P120)<br/>2B-622-150 (P150) | 2B-622-180 (P180)<br/>2B-622-220 (P220) | 2B-622-240 (P240)<br/>2B-622-320 (P320) | 2B-622-400 (P400)<br/>2B-622-500 (P500) | 2C-622-600 (P600)<br/>2C-622-800 (P800) | 2C-622-1000 (P1000)<br/>2C-622-1200 (P1200) | 2C-622-1500 (P1500)<br/><br/>Mirka 3" & 6" Interface Pads<br/>A wide variety of interface pads ensure that just about any sanding disc can deliver maximum performance while working on any sanding surface. Mirka offers interface pads with no foam, skinny foam, fat foam, stiff foam, and soft foam.<br/><br/>Mirka MR-350 3" Bulldog Palm Sander<br/>5mm orbit diameter | 0-12,000 RPM<br/><br/>Mirka 3" Sanding Products<br/>9133 | MR-350 | Microstar Discs<br/><br/>Mirka Microstar 3" & 6" Dry-Sanding Discs are designed for use without water. They are engineered to absolutely resist debris loading. Since no water is used during sanding, it is much easier to gauge sanding results. Microstar Dry-Sanding Discs are available in the following grades:<br/><br/>3" diameter<br/>FM-608-800 (P800) | FM-608-1000 (P1000)<br/>FM-608-1200 (P1200) | FM-608-1500 (P1500)<br/>FM-608-2000 (P2000) | FM-608-2500 (P2500)<br/><br/>6" diameter<br/>FM-622-800 (P800) | FM-622-1000 (P1000)<br/>FM-622-1200 (P1200) | FM-622-1500 (P1500)<br/>FM-622-2000 (P2000) | FM-622-2500 (P2500)<br/><br/>Mirka 3" & 6" Interface Pads<br/>A wide variety of interface pads ensure that just about any sanding disc can deliver maximum performance while working on any sanding surface. Mirka offers interface pads with no foam, skinny foam, fat foam, stiff foam, and soft foam.<br/><br/>Mirka MR-350 3" Bulldog Palm Sander<br/>5mm orbit diameter | 0-12,000 RPM<br/><br/>About Mirka Interface Pads<br/><br/>Interface Pads are placed between backing plates and sanding discs, with the intent to substantially improve overall sanding performance. Interface pads enable sanding discs to conform to their maximum ability.They also assist in distributing machine weight, and user-applied pressure.<br/><br/>An interface pad can decrease uncontrolled wandering of the machine, which occurs when a disc cannot conform to the surface being sanded (due to backing plate rigidity). If the choice is made to use only a portion of the disc by intentionally tilting the machine, the portion in contact with the sanding surface receives adequate support from the interface pad.<br/><br/>HP3-VELCRO<br/>3" Dome-Shaped Velcro Hand Sanding Pad.<br/><br/>Shown with the included 3" Foam Velcro Interface Pad.<br/><br/>HP3-VELCRO<br/><br/>3" Dome-Shaped Velcro Hand Sanding Pad.<br/><br/>Left: Shown with a Mirka® Autonet Mesh Fabric Sanding Disc, and a Mirka 9947 Pad Protector.<br/>Right: Shown with a Mirka® 1033 3" Foam Velcro Interface Pad.<br/><br/>HP3-VELCRO<br/>3" Velcro Dome Hand Sanding Pad.<br/><br/>Shown with Mirka 9133 3" Abranet Velcro Interface Pad.<br/><br/>HP3-VELCRO<br/>3" Velcro Dome Hand Sanding Pad.<br/><br/>Shown with Mirka 9133 3" Abranet Velcro Interface Pad, and a 3" Autonet Mesh Fabric Sanding Disc.<br/><br/>
Click to enlarge image(s)


Designed for use with Abranet and Autonet Sanding Discs.

The open mesh design employed in Abranet and Autonet products may allow the hook material of a backing plate to protrude through the mesh. If this occurs, the backing plate hooks will degrade quickly. Even worse, the hook material can cause surface marring! Avoid this problem by installing this Interface Pad. Also available in a 6" version: 9166

The Mirka 9133 Abranet Interface Pad protects the backing plate and sanding surface, all the while increasing adhesion of sanding discs to the backing plate. A soft and pliable foam interlayer (3/16" tall) allows an attached disc to flex and conform to curved or complex shapes. Using a vacuum system for ultra-clean sanding? Three vacuum holes ensure a thorough cleaning of the sanding surface when using net mesh discs.

Add a Dome-Style Hand Sanding Pad. This uniquely shaped block makes sanding by hand a breeze to accomplish. Its yellow cushiony material is soft, making it easy to grasp, even when wet. The Velcro face is molded into place (not glued), so pad failure is  unlikely. A soft interface pad is included (interface is not a Mirka product).

Add a Pad Protector. No need for cushioning? Check out the Mirka Pad Protector. This simple device will not only protect the backing plate and surface being sanded, it also increases adhesion of the sanding disc to the backing plate. Since the Pad Protector is only about 1/16" thick, in most cases it will not affect the leveling capability of the disc.

 Mirka 3" Velcro Backing Plates can be found here.

 Mirka 3" Velcro Interface Pads: 1033 | 9947 | 9133

 Mirka 3" Velcro Sanding Discs can be found here:
        Abralon | Abranet | Autonet | Silver | Microstar

 More Interface Pad info: Interface Pad Facts.

Part Number:
1066
 Actual Diameter:
5 - 7/8"
 Height:
1/2"
 Backing Material:
HOOK/LOOP
If you were to own just one 6" interface pad, this may be the one you'd want.  Why?  Versatility!  This pad features a "middle of the road" firmness, so it works well on a multitude of tasks. Its 1/2" pad height is handy, too.  Using a vacuum system?  Six holes ensure thorough cleaning of the disc and sanding surface.
Price:
$11.97
Qty:
Mirka 6" Interface Pad- "1/2" thick

Mirka 6" Interface Pad- "1/2" thick

Mirka 6" Interface Pad- "1/2" thick
Click to enlarge image(s)


A high quality, all-purpose interface.

Interface pads are a necessity for machine sanding. If you were to own just one interface pad, this may be the one you'd want!

The foam material used to make this pad features a middle of the road firmness, while its 1/2" height is sufficient for most tasks.

Should you decide to pair your machine with a vacuum system, six holes ensure ample cleaning of the sanding surface and disc.

Looking for a similarly versatile pad with a bit more firmness and a little less height?
Try the Mirka 1066F.

Note: Due to its 1/2" height, this interface pad may lessen sanding disc movement in relation to the backing plate, especially when used with small stroke machines.

When used with random orbital machines, backing plate rotation may also be affected.

To view our entire interface pad lineup, check out the Interface Pad Page here.
To learn more about interface pads, check out the Interface Pad Info Page here.
Quantity Price
1 - 1
$12.97
2 - 2
$11.54 save 11%
3 - 3
$10.64 save 18%
4+
$9.73 save 25%
Specifications
  • Actual diameter: 5-7/8"
  • Actual height: 1/2"

Part Number:
1066F
 Actual Diameter:
5 - 3/4"
 Height:
3/8"
 Backing Material:
HOOK/LOOP
Ahh, a super nice 6" interface pad.  Its foam center is firmer than most, enabling it to transfer machine movements accurately.  I really like the height, too.  The hook material is interesting- each "hook" is straight, with a little sphere on the end.  Easy on, easy off.  Any serious "interface aficionado" MUST own one.
Price:
$11.97
Qty:
Mirka 6" Firm-Faced Interface Pad- 3/8" thick

Mirka 6" Firm-Faced Interface Pad- 3/8" thick

Mirka 6" Firm-Faced Interface Pad- 3/8" thick
Click to enlarge image(s)


Minimize the loss of machine motion while maximizing flexibility of the sanding disc.

Interface pads are oh-so useful. However, as their foam centers twist, compress, and rebound, machine motion can be dramatically affected.

This pad has been designed to minimize this side-effect, all the while delivering increased flexibility of the disc.  Compared to most other interface pads, this one transfers machine motion fairly unscathed.

Should you decide to pair your machine with a vacuum system, fifteen holes ensure ample cleaning of the sanding surface and disc.

Looking for a similarly versatile pad with a bit more pliability and a little more height?
Try the Mirka 1066.

Note: Due to its 3/8" height, this interface pad may lessen sanding disc movement in relation to the backing plate, especially when used with small stroke machines.

When used with random orbital machines, backing plate rotation may also be affected.

To view our entire interface pad lineup, check out the Interface Pad Page here.
To learn more about interface pads, check out the Interface Pad Info Page here.
Specifications
  • Actual diameter: 5-13/16"

  • Attachment material:
    Hook & loop
  • Actual height: 3/8"

  • Fifteen holes ensure ample vacuuming of the sanding surface and disc

Part Number:
1066SF
 Actual Diameter:
5 - 3/4"
 Height:
3/4"
 Backing Material:
MICRO HOOK/LOOP
Need to sand something that is super-curvy or oddly shaped? You'll want one of these 6" interface pads! It's 3/4" height will enable a sanding disc to reach its maximum "flex" potential. The micro-hook face firmly locks discs into place, and will not protrude into the face of the disc. A nice addition to your interface arsenal.
Price:
$11.97
Qty:
Mirka 6" Soft-Faced Interface Pad- 3/4" thick

Mirka 6" Soft-Faced Interface Pad- 3/4" thick

Mirka 6" Soft-Faced Interface Pad- 3/4" thick
Click to enlarge image(s)


For wickedly-curved surfaces, you'll want this soft & puffy interface.

At some point, the time may come when you'll need to sand a sphere-shaped item, a large cylinder, or even a wickedly-curved fender. Be prepared! This is the interface you'll need.

The foam used to make this interface is a bit stiffer than the type used to make the Mirka 9166. However, the height of this pad increases cushioning ability versus the 9166.

Available in 3" & 6" diameters (3" version is 1/2" tall, 3" part #1033).

Note: Due to its 3/4" height, this interface pad may lessen sanding disc movement in relation to the backing plate, especially when used with small stroke machines.

When used with random orbital machines, backing plate rotation may also be affected.

To view our entire interface pad lineup, check out the Interface Pad Page here.
To learn more about interface pads, check out the Interface Pad Info Page here.
Specifications
  • #1033 3" pad:
    actual diameter 2-7/8"
    actual height 1/2"
  • #1066SF 6" pad:
    actual diameter 5-3/4"
    actual height 3/4"

Part Number:
9956
 Actual Diameter:
5 - 7/8"
 Height:
1/8"
 Backing Material:
HOOK/LOOP
This 6" pad protector is designed for use with Mirka net mesh products (such as Abranet® and Autonet™ discs). It will prevent the backing plate hook material from protruding through the disc.  Sand without one, and backing plate damage or surface marring may occur. They're inexpensive and durable. Don't skimp- use one!
Price:
$5.49
Qty:
Mirka Abranet® 6" Pad Protector- 1/8" thick

Mirka Abranet® 6" Pad Protector- 1/8" thick

Mirka Abranet® 6" Pad Protector- 1/8" thick
Click to enlarge image(s)


Designed for use with Abranet and Autonet Sanding Discs.

The open mesh design employed in Abranet and Autonet products may allow the hook material of a backing plate to protrude through the mesh. If this occurs, the backing plate hooks will degrade quickly. Even worse, the hook material can cause surface marring! Avoid this problem by installing a Pad Protector. Also available in a 3" version: 9947

This simple device will not only protect the backing plate and surface being sanded, it also increases adhesion of the sanding disc to the backing plate. Since the Pad Protector is only about 1/16" thick, in most cases it will not affect the leveling capability of the disc.

Add a 3M® 05791 Hookit 6" Flexible Velcro Hand Pad.
This versatile Flexible Round Hand Pad helps to distribute pressure much more evenly.  The elastic strap keeps the pad attached to your hand while you sand, increasing comfort and control.  If you use a water bucket while wet sanding, you'll appreciate this fact:  It floats!

More info: 6" Flexible Velcro Hand Pad

Add a 6" 3M® 05792 Hookit 6" Half-Round Velcro Hand Pad.
This taco-shaped pad is somewhat rigid, with only minimal flexibility. Its straight edge features a smooth 1/4" radius, enabling it to be used inside inward-curved areas. Although designed for use with 6-inch diameter discs, it is not an exact fit: it's as if someone didn't account for the 1/4" radius. Regardless, this 3M version is the best fitting (and thinnest) available.

More info: 6" Half-Round Velcro Hand Pad

Add an interface pad. The time may come when you'll need to sand a sphere-shaped item, a cylinder, or a wickedly-curved fender. To increase cushioning and shapability of net mesh sanding discs, this is the interface pad you'll need. The Mirka 9166 6" Abranet Interface Pad measures 5-7/8" in diameter, and is 3/16" tall. Note that due to its height, this interface pad may lessen sanding disc movement, particularly if paired with small stroke machines. Also available in a 3" version: 9133

Mirka 6" Velcro Backing Plates can be found here.

Mirka 6" Velcro Interface Pads: 1066 | 9956 | 9166

Mirka 6" Velcro Sanding Discs can be found here:
        Abralon | Abranet | Autonet | Silver | Microstar

More Interface Pad info: Interface Pad Facts.
Quantity Price
1 - 1
$6.95
2 - 2
$6.19 save 11%
3 - 3
$5.70 save 18%
4+
$5.21 save 25%
Specifications
  • #9947 3" pad: actual diameter 2-7/8"

  • Compatible with Abranet® or Autonet™ discs

  • Pad Protector is MANDATORY to use if no other interface pad is used between the sanding disc and backing plate

  • Greatly improves the adhesion of discs to the backing plate
  • #9956 6" pad: actual diameter 5-7/8"

  • Pad protector attaches to any hook & loop backing plate

  • Acts as a barrier so the backing plate hook material will not protrude through the sanding disc

  • Extends the life of the backing plate

Part Number:
9166
 Actual Diameter:
5 - 3/4"
 Height:
3/8"
 Backing Material:
HOOK/LOOP
This 6" interface pad is designed for use with Mirka net mesh products (such as Abranet® and Autonet™ discs). What's so different about it? The hooks! They're pliable and long, with tips that are shaped to grab ahold of the loop. They bend easily to resist marring, yet really lock net mesh discs safely into place.
Price:
$11.97
Qty:
Mirka Abranet® 6" Interface Pad- 3/8" thick

Mirka Abranet® 6" Interface Pad- 3/8" thick

Mirka Abranet® 6" Interface Pad- 3/8" thick
Click to enlarge image(s)


Designed for use with Abranet and Autonet Sanding Discs.

This interface pad was primarily designed for use with net mesh discs such as Abranet® and Autonet™, but works well with all hook & loop systems.

The open mesh design employed in Abranet® and Autonet™ products may allow the hook material of a typical backing plate to protrude through the mesh.   If this occurs, the backing plate hooks will degrade quickly. Even worse, the hook material can cause surface marring!

Avoid this problem by installing this interface pad.  Its hook characteristics have been optimized to perform exceptionally well with net mesh products.

The foam center is soft and very pliable, allowing an attached disc to flex and conform to curved or complex shapes. Using a vacuum system with your machine? This interface features over sixty vacuum holes, assuring a thorough cleaning of the sanding surface and disc. Available in 3" & 6" diameters (6" part #9133).

Notes:
1. If you don't need the extra cushioning for your net mesh discs but wish to use an appropriate interface, check out Mirka's Pad Protector.  They are available in 3" & 6" diameters (3" part #9947, and 6" part #9956).

2. Due to its 3/8" height, this interface pad may lessen sanding disc movement in relation to the backing plate, especially when used with small stroke machines.  When used with random orbital machines, backing plate rotation may also be affected.

The open mesh design employed in Abranet and Autonet products may allow the hook material of a backing plate to protrude through the mesh. If this occurs, the backing plate hooks will degrade quickly. Even worse, the hook material can cause surface marring! Avoid this problem by installing a Pad Protector. Also available in a 3" version: 9947

This simple device will not only protect the backing plate and surface being sanded, it also increases adhesion of the sanding disc to the backing plate. Since the Pad Protector is only about 1/16" thick, in most cases it will not affect the leveling capability of the disc.

Add a 3M® 05791 Hookit 6" Flexible Velcro Hand Pad.
This versatile Flexible Round Hand Pad helps to distribute pressure much more evenly.  The elastic strap keeps the pad attached to your hand while you sand, increasing comfort and control.  If you use a water bucket while wet sanding, you'll appreciate this fact:  It floats!

More info: 6" Flexible Velcro Hand Pad

Add a 6" 3M® 05792 Hookit 6" Half-Round Velcro Hand Pad.
This taco-shaped pad is somewhat rigid, with only minimal flexibility. Its straight edge features a smooth 1/4" radius, enabling it to be used inside inward-curved areas. Although designed for use with 6-inch diameter discs, it is not an exact fit: it's as if someone didn't account for the 1/4" radius. Regardless, this 3M version is the best fitting (and thinnest) available.

More info: 6" Half-Round Velcro Hand Pad


Mirka 6" Velcro Backing Plates can be found here.

Mirka 6" Velcro Interface Pads: 1066 | 1066F | 1066SF | 9956

Mirka 6" Velcro Sanding Discs can be found here:
        Abralon | Abranet | Autonet | Silver | Microstar

More Interface Pad info: Interface Pad Facts.
Quantity Price
1 - 1
$12.97
2 - 2
$11.54 save 11%
3 - 3
$10.64 save 18%
4+
$9.73 save 25%
Specifications
  • #9133 3" pad:
    actual diameter 2-7/8"
    actual height 1/2"

  • Compatible with Abranet® or Autonet™ (net mesh) discs

  • Greatly improves the adhesion of net mesh discs to the backing plate
  • #9166 6" pad:
    actual diameter 5-3/4"
    actual height 1/2"

  • Pad Protector or net mesh compatible interface is MANDATORY to use with net mesh discs if no other interface pad is used between the sanding disc and backing plate